Same-day appointments across the San Fernando Valley when you call before 3pm.
Mon–Fri 7am–7pm · Sat 8am–5pm info@skillgaragedoorrepair.com
November 16, 2026 · 6 min read

Garage door closes then reverses: 6 causes and how to tell them apart

A door that reverses on the way down is usually a safety device doing its job. Here are six causes, how to tell them apart, and when to call a technician in Valley Village.

Skill Garage Door Valley Village, CA Mon–Fri 7am–7pm · Sat 8am–5pm
Garage door closes then reverses: 6 causes and how to tell them apart

A garage door that starts down and then pulls back up is not usually a mysterious electrical fault. In most cases one of a small number of parts is doing exactly what it was designed to do, or a mechanical problem is being read by the opener as an obstruction. The trick is working out which, because the fix for a dirty photo-eye is very different from the fix for a binding track.

Below are the six causes we see most often on doors across Valley Village and the surrounding San Fernando Valley, with a simple way to tell each one apart before anyone touches a part.

1. The photo-eye sensors are blocked, dirty or misaligned

The photo-eyes are the two small lenses mounted at the bottom of the tracks, one on each side, about 15 cm above the floor. One sends an invisible beam; the other receives it. If the beam is broken while the door is closing, the opener reverses immediately, usually within a second or two of the door starting down.

Look for the obvious first: a bin handle, a broom, a recycling box or a bag of garden waste sitting in the line of sight. Then check the lenses themselves. Dust, cobwebs and spider nests on the lens will scatter the beam just enough to trip it. Wipe both lenses with a soft cloth. Finally, check alignment — each sensor has a small indicator light, and it should be steady, not flickering. A sensor knocked slightly out of line by a car bumper or a wheelbarrow will cause a door that reverses at random.

2. A binding track or worn roller is tripping the force setting

This one looks electrical but is mechanical. Openers are set to expect a certain amount of resistance as the door travels. If a track is bent, a section of track is out of plumb, or a roller is worn flat and dragging, the door binds on the way down. The opener reads that resistance as an obstruction and reverses.

The tell is the behaviour: the door reverses at roughly the same point on the way down each time, and it may hesitate or slow just before it does. Run the door by hand with the opener disengaged — most openers have a red release cord — and feel for a tight spot. Look along the track for dents, and check the rollers for flat spots or wobble. Do not simply turn the force setting up to push through it; that masks the problem and strains the opener.

3. Travel limits set too far down

The down limit switch tells the opener where the closed position is. If it is set too far, the door reaches the floor and the opener keeps driving, the door bows slightly and the safety system reverses it. The result is a door that touches down and bounces straight back up.

You can usually spot this by watching the bottom seal: if the door presses hard into the floor for a moment before reversing, the limit is the likely cause. On most openers the limit is adjusted with a screw or a pair of buttons on the motor head, but the correct setting depends on the door and the opener model. This is a job where a technician sets it and then tests the reversal with a small object under the door.

4. A sagging top panel or loose hinge catching the beam

Sometimes the obstruction is the door itself. A top panel that has sagged, a hinge that has worked loose, or a roller that has pulled slightly out of its bracket can hang low enough to break the photo-eye beam as the door comes down. The door reverses, and the sensors look perfectly fine when you inspect them with the door open.

To tell this apart from a sensor fault, watch the door from the side as it closes and see whether anything on the door passes through the beam line just before it reverses. Check the hinges along the bottom two panels for play, and look along the top panel for a visible sag. A loose hinge is a small repair; a sagging panel is worth inspecting properly, because it affects how the door sits in the tracks.

5. Sunlight straight into a sensor lens

Infrared sensors can be overwhelmed by direct low sun. If the door reverses only in the late afternoon, at roughly the same time each day, and works normally in the morning or on cloudy days, sunlight is the likely cause. The receiving lens is being flooded with light and cannot distinguish the beam.

The fix is usually a small shroud or a repositioned bracket rather than a new sensor. Note the time of day and which side of the door faces the sun — that detail saves a lot of diagnostic time.

6. The opener is flashing a fault code

If the door reverses halfway down and the opener's light flashes a set number of times, the control board is reporting a specific fault. Count the flashes and check the manual for that opener model before changing any parts. A repeated pattern of flashes is the board telling you what it thinks is wrong — often a sensor issue, sometimes a limit or force problem.

This is also the point to stop and call. A technician can read the code, test the safety reverse with a proper obstruction test, and check the torsion spring, drum and cables while they are there. If you are in North Hollywood, Studio City, Sherman Oaks, Encino, Van Nuys, Burbank or Glendale, we cover those neighbourhoods from our base in Valley Village.

What to do next

Start with the simple checks: clear the beam line, wipe the lenses, note when the door reverses and whether the opener light flashes. If the cause is not obvious, or the door binds, bounces or reverses at the same point every time, book a garage door repair visit. A technician will diagnose the door and opener, explain what needs doing and quote before any work begins. You can also request a quote online, or call (877) 976-2797.

Common questions

Why does it reverse right after touching the floor? Usually the travel limit is set too far down, so the door hits the concrete and the opener treats it as an obstruction.

Do any sensors cause it? Yes — a misaligned photo eye reverses the door instantly, and it is the first thing to check.

Can I hold the button to force it closed? No — that overrides a safety device. Fix the cause instead.

More from the workshop

Related reading

Talk to a technician

Want this sorted properly?

Call (877) 976-2797 and describe what your door or gate is doing. Most repairs are quoted on site and finished the same visit.

Call now Free quote