Same-day appointments across the San Fernando Valley when you call before 3pm.
Mon–Fri 7am–7pm · Sat 8am–5pm info@skillgaragedoorrepair.com
Iron · wood · aluminium

Custom gate installation

A new gate is a fence line, a security decision and a machine all at once. We size the gate to your driveway, set the posts into proper footings, hang the gate so it swings free, and — if you want it automatic — choose an operator rated for the finished weight.

Swing and sliding gates in iron, steel, wood and aluminium Posts and footings set for the gate weight Operator sized to the gate, not the other way round
Custom gate installation — garage and gate work in the San Fernando Valley
Choosing the gate

Swing or slide, and what decides it

Swing gates need clearance behind and in front of them, and they must clear the driveway slope through their whole arc. Sliding gates need a straight run of wall or fence for the gate to travel beside, and a flat track area. On a narrow Valley driveway with a steep apron, the choice is often made for you.

Material follows function: ornamental iron for security and sight lines, wood for privacy and warmth, aluminium for a wood look with less maintenance, and steel where a heavier gate is wanted.

  • Iron and steel — strong, long lived, repairable, needs periodic rust care
  • Wood — privacy and warmth, needs sealing and a solid frame
  • Aluminium — light, rust-free, good for wide sliding gates
  • Design details — pickets, scrolls, panel infill, colour matching to the house
Getting it right

The unglamorous parts that matter

The gate is the visible part, but the posts and footings decide whether it still hangs straight in five years. We set posts in concrete at a depth suited to the gate size and the soil, brace the hinge post, and validate that the driveway cross-slope lets the gate swing without dragging.

If the gate will be automatic, the operator sizing happens before the gate is built. A sliding gate that is too heavy for its operator will eat motors, and a swing gate with too little clearance will hit the driveway before it opens fully.

The install

From measurement to handover

We measure the opening and driveway, agree the design and finish, set the posts, hang the gate, fit the hardware and — where requested — install and programme the operator, safety devices, keypad and remotes.

Before we leave we walk you through the operation: how the manual release works, how to test the safety devices, and what maintenance the gate needs each year.

Safety & rules

Automation, safety and what the city expects

An automatic gate needs entrapment protection — photo eyes, safety edges or induction loops that stop and reverse the gate if something is in the way. That is not optional equipment; it is the difference between a convenient gate and a hazard for children, pets and delivery drivers.

Height, setback from the property line and visibility at the driveway are governed by local rules, and the requirements differ between the City of Los Angeles and neighbouring jurisdictions. We will tell you what we know applies to your property and flag anything that should be confirmed with the city before the gate is fabricated.

  • Photo eyes or safety edges on every automatic gate
  • Manual release that works during a power cut
  • Gate travel stops and reverses on contact
  • Keypad, intercom and remote access agreed up front
Getting a quote

What we need to price a gate properly

A gate quote is only as good as the measurements behind it. Send photos and a few numbers and we can give you a realistic price instead of a guess.

  • Photos of the opening from both sides, plus the driveway
  • Width and height you want the gate to be
  • Driveway slope and how much room there is behind the gate
  • Material and style preference, or a photo of a gate you like
  • Swing or sliding, manual or automatic
  • Anything buried near the posts — irrigation, power, gas lines
Questions

Custom gate installation — common questions

How long does a new gate take?

A stock-size gate can be installed in a day or two including posts. A custom-built gate has a fabrication lead time of roughly two to four weeks, then one to two days on site. We give you the timeline with the quote.

Do I need a permit for a driveway gate?

It depends on the height, the property line and whether the gate is automatic — the City of Los Angeles has rules on height, setback and visibility at driveways. We will tell you what we know to be required for your situation and recommend checking with the city before fabrication if a permit applies.

Can I automate a gate later?

Yes, if the gate was built with that in mind: a suitable hinge post, room for the operator, and a gate weight within a sensible motor range. Tell us when the gate is being quoted and we will make sure it can be automated later instead of rebuilt.

Get a price

Price for custom gate installation

Send a few details and we will call back with a firm price and the next available window. If you are not sure which service you need, describe the symptoms — that is usually enough.

  • Diagnosis on site before any work
  • Firm price approved by you, in writing
  • Parts stocked for common failures
  • Safety reverse tested before we leave

Request a free quote

Tell us what is happening with the door or gate. We will call you back with a price and the earliest service window.

Or call (877) 976-2797 — a person answers Mon–Fri 7am–7pm · Sat 8am–5pm. We only use your details to reply about this job.

Also relevant

Services people book with this one

Talk to a technician

Need custom gate installation today?

Call (877) 976-2797 and describe what the door is doing. Most repairs are quoted on site and finished the same visit.

Call now Free quote